X-Git-Url: https://bilbo.iut-bm.univ-fcomte.fr/and/gitweb/GMRES2stage.git/blobdiff_plain/42bad55fb961978dd2a38a0236bc43cc8b5ab7cf..ad91b931741db537cefe135f277f1fd5065db21f:/paper.tex diff --git a/paper.tex b/paper.tex index 15a45f0..6292705 100644 --- a/paper.tex +++ b/paper.tex @@ -428,16 +428,16 @@ Email: lilia.ziane@inria.fr} \begin{abstract} -In this article, a two-stage iterative method is proposed to improve the -convergence of Krylov based iterative ones, typically those of GMRES variants. The +In this article, a two-stage iterative algorithm is proposed to improve the +convergence of Krylov based iterative methods, typically those of GMRES variants. The principle of the proposed approach is to build an external iteration over the Krylov method, and to frequently store its current residual (at each GMRES restart for instance). After a given number of outer iterations, a minimization step is applied on the matrix composed by the saved residuals, in order to -compute a better solution while making new iterations if required. It is proven that +compute a better solution and to make new iterations if required. It is proven that the proposal has the same convergence properties than the inner embedded method itself. Experiments using up to 16,394 cores also show that the proposed algorithm -run around 7 times faster than GMRES. +runs around 5 or 7 times faster than GMRES. \end{abstract} \begin{IEEEkeywords} @@ -759,16 +759,16 @@ Table~\ref{tab:01}, we show the matrices we have used and some of them characteristics. For all the matrices, the name, the field, the number of rows and the number of nonzero elements is given. -\begin{table*}[htbp] +\begin{table}[htbp] \begin{center} \begin{tabular}{|c|c|r|r|r|} \hline Matrix name & Field &\# Rows & \# Nonzeros \\\hline \hline crashbasis & Optimization & 160,000 & 1,750,416 \\ -parabolic\_fem & Computational fluid dynamics & 525,825 & 2,100,225 \\ +parabolic\_fem & Comput. fluid dynamics & 525,825 & 2,100,225 \\ epb3 & Thermal problem & 84,617 & 463,625 \\ -atmosmodj & Computational fluid dynamics & 1,270,432 & 8,814,880 \\ -bfwa398 & Electromagnetics problem & 398 & 3,678 \\ +atmosmodj & Comput. fluid dynamics & 1,270,432 & 8,814,880 \\ +bfwa398 & Electromagnetics pb & 398 & 3,678 \\ torso3 & 2D/3D problem & 259,156 & 4,429,042 \\ \hline @@ -776,7 +776,7 @@ torso3 & 2D/3D problem & 259,156 & 4,429,042 \\ \caption{Main characteristics of the sparse matrices chosen from the Davis collection} \label{tab:01} \end{center} -\end{table*} +\end{table} The following parameters have been chosen for our experiments. As by default the restart of GMRES is performed every 30 iterations, we have chosen to stop @@ -882,23 +882,20 @@ number can seem relatively small. In fact, for some applications that need a lot of memory, the number of components per processor requires sometimes to be small. + + In this Table, we can notice that TSIRM is always faster than FGMRES. The last column shows the ratio between FGMRES and the best version of TSIRM according to the minimization procedure: CGLS or LSQR. Even if we have computed the worst case between CGLS and LSQR, it is clear that TSIRM is alsways faster than FGMRES. For this example, the multigrid preconditionner is faster than SOR. The gain between TSIRM and FGMRES is more or less similar for the two -preconditioners. - -In Figure~\ref{fig:01}, the number of iterations per second corresponding to -Table~\ref{tab:01} is displayed. It should be noticed that for TSIRM, only the -iterations of the Krylov solver are taken into account. Iterations of CGLS or -LSQR are not recorded but they are time-consuming. It can be noticed that the -number of iterations per second of FMGRES is constant whereas it decrease with -TSIRM with both preconditioner. This can be explained by the fact that when the -number of core increases the time for the minimization step also increases but -it is also more efficient to reduce the number of iterations. - +preconditioners. Looking at the number of iterations to reach the convergence, +it is obvious that TSIRM allows the reduction of the number of iterations. It +should be noticed that for TSIRM, in those experiments, only the iterations of +the Krylov solver are taken into account. Iterations of CGLS or LSQR were not +recorded but they are time-consuming. In general each $max\_iter_{kryl}*s$ which +corresponds to 30*12, there are $max\_iter_{ls}$ which corresponds to 15. \begin{figure}[htbp] \centering @@ -908,6 +905,17 @@ it is also more efficient to reduce the number of iterations. \end{figure} +In Figure~\ref{fig:01}, the number of iterations per second corresponding to +Table~\ref{tab:01} is displayed. It can be noticed that the number of +iterations per second of FMGRES is constant whereas it decrease with TSIRM with +both preconditioner. This can be explained by the fact that when the number of +core increases the time for the minimization step also increases but, generally, +when the number of cores increases, the number of iterations to reach the +threshold also increases, and, in that case, TSIRM is more efficient to reduce +the number of iterations. So, the overall benefit of using TSIRM is interesting. + + + @@ -935,7 +943,7 @@ it is also more efficient to reduce the number of iterations. \end{table*} - +In Table~\ref{tab:04}, some experiments with example ex54 on the Curie architecture are reported. \begin{table*}[htbp]