From: couturie Date: Fri, 13 Jan 2017 15:22:10 +0000 (+0100) Subject: test commit X-Git-Url: https://bilbo.iut-bm.univ-fcomte.fr/and/gitweb/JournalMultiPeriods.git/commitdiff_plain/851c4bad39e11ad78c3f12eb0b7324fcaa29f60b?ds=inline test commit --- diff --git a/R2/CR.pdf b/R2CR.pdf similarity index 100% rename from R2/CR.pdf rename to R2CR.pdf diff --git a/article.tex b/article.tex index b0a1878..329426f 100644 --- a/article.tex +++ b/article.tex @@ -590,15 +590,6 @@ integer program contains $A*T$ variables of type $X_{t,j}$, $P*T$ overcoverage variables and $P*T$ undercoverage variables. The number of constraints is equal to $P*T$ (for constraints (\ref{eq16})) $+$ $A$ (for constraints (\ref{eq144})). -\iffalse -\subsection{Sensing phase} - -The sensing phase consists of $T$ rounds. Each sensor node in the subregion will -receive an Active-Sleep packet from WSNL, informing it to stay awake or to go to -sleep for each round of the sensing phase. Algorithm~\ref{alg:MuDiLCO}, which -will be executed by each sensor node~$s_j$ at the beginning of a period, -explains how the Active-Sleep packet is obtained. -\fi \section{Experimental framework} \label{exp} @@ -676,65 +667,6 @@ the following we have set the number of subregions to~16 \textcolor{blue}{as AVR ATmega103L microcontroller~\cite{raghunathan2002energy} to use numerical values.} -\iffalse -\subsection{Energy model} - -We use an energy consumption model proposed by~\cite{ChinhVu} and based on -\cite{raghunathan2002energy} with slight modifications. The energy consumption -for sending/receiving the packets is added, whereas the part related to the -sensing range is removed because we consider a fixed sensing range. - -For our energy consumption model, we refer to the sensor node Medusa~II which -uses an Atmels AVR ATmega103L microcontroller~\cite{raghunathan2002energy}. The -typical architecture of a sensor is composed of four subsystems: the MCU -subsystem which is capable of computation, communication subsystem (radio) which -is responsible for transmitting/receiving messages, the sensing subsystem that -collects data, and the power supply which powers the complete sensor node -\cite{raghunathan2002energy}. Each of the first three subsystems can be turned -on or off depending on the current status of the sensor. Energy consumption -(expressed in milliWatt per second) for the different status of the sensor is -summarized in Table~\ref{table4}. - -\begin{table}[ht] -\caption{The Energy Consumption Model} -\centering -\begin{tabular}{|c|c|c|c|c|} - \hline -Sensor status & MCU & Radio & Sensing & Power (mW) \\ [0.5ex] -\hline -LISTENING & on & on & on & 20.05 \\ -\hline -ACTIVE & on & off & on & 9.72 \\ -\hline -SLEEP & off & off & off & 0.02 \\ -\hline -COMPUTATION & on & on & on & 26.83 \\ -\hline -\end{tabular} - -\label{table4} -\end{table} - -For the sake of simplicity we ignore the energy needed to turn on the radio, to -start up the sensor node, to move from one status to another, etc. -Thus, when a sensor becomes active (i.e., it has already chosen its status), it -can turn its radio off to save battery. MuDiLCO uses two types of packets for -communication. The size of the INFO packet and Active-Sleep packet are 112~bits -and 24~bits respectively. The value of energy spent to send a 1-bit-content -message is obtained by using the equation in ~\cite{raghunathan2002energy} to -calculate the energy cost for transmitting messages and we propose the same -value for receiving the packets. The energy needed to send or receive a 1-bit -packet is equal to 0.2575~mW. - -The initial energy of each node is randomly set in the interval $[500;700]$. A -sensor node will not participate in the next round if its remaining energy is -less than $E_{R}=36~\mbox{Joules}$, the minimum energy needed for the node to -stay alive during one round. This value has been computed by multiplying the -energy consumed in active state (9.72 mW) by the time in second for one round -(3600 seconds). According to the interval of initial energy, a sensor may be -alive during at most 20 rounds. -\fi - \subsection{Metrics} \textcolor{blue}{To evaluate our approach we consider the performance metrics @@ -806,21 +738,7 @@ indicate the energy consumed by the whole network in round $t$. %nodes have been drained of their energy or each sensor network monitoring an area has become disconnected. \end{enumerate} -\iffalse -\begin{enumerate} - \setcounter{5} -\item {{\bf Execution Time}:} a sensor node has limited energy resources and - computing power, therefore it is important that the proposed algorithm has the - shortest possible execution time. The energy of a sensor node must be mainly - used for the sensing phase, not for the pre-sensing ones. - -\item {{\bf Stopped simulation runs}:} a simulation ends when the sensor network - becomes disconnected (some nodes are dead and are not able to send information - to the base station). We report the number of simulations that are stopped due - to network disconnections and for which round it occurs. -\end{enumerate} -\fi \section{Experimental results and analysis} \label{analysis}