update 3

[ThesisAli.git] / CHAPITRE_01.tex

diff --git a/CHAPITRE_01.tex b/CHAPITRE_01.tex
index 76780d90864b3375f4346131ecaa8b18f446130f..971dbebb563a2e15b7a906ba1382531ef3aea2e1 100644 (file)
--- a/CHAPITRE_01.tex
+++ b/CHAPITRE_01.tex
@@ -407,6 +407,7 @@ In this section, two energy consumption models are explained. The first model ca
 
 
 \subsection{Radio Energy Dissipation Model}
 
 
 \subsection{Radio Energy Dissipation Model}

+\label{ch1:sec9:subsec1}

 Since the communication unit is the most energy-consuming part inside the sensor node, and accordingly there are many authors used the radio energy dissipation model that proposed in~\cite{ref109,ref110} as energy consumption model during the simulation and evaluation of their works in WSNs. Figure~\ref{RDM} shows the radio energy dissipation model.
 \begin{figure}[h!]
 \centering
 Since the communication unit is the most energy-consuming part inside the sensor node, and accordingly there are many authors used the radio energy dissipation model that proposed in~\cite{ref109,ref110} as energy consumption model during the simulation and evaluation of their works in WSNs. Figure~\ref{RDM} shows the radio energy dissipation model.
 \begin{figure}[h!]
 \centering


@@ -441,6 +442,7 @@ The radio energy dissipation model have been considered only the energy consumed
 
 
 \subsection{Our Energy Consumption Model}
 
 
 \subsection{Our Energy Consumption Model}

+\label{ch1:sec9:subsec2}

 In this dissertation, the coverage protocols have been used an energy consumption model proposed by~\cite{ref111} and based on \cite{ref112} with slight  modifications.  The energy consumption for  sending/receiving the packets is added, whereas the  part related to the sensing range is removed because we consider a fixed sensing range.
 For our energy consumption model, we refer to the sensor node Medusa~II which uses an Atmels  AVR ATmega103L microcontroller~\cite{ref112}. The typical architecture  of a  sensor  is composed  of  four  subsystems: the  MCU subsystem which is capable of computation, communication subsystem (radio) which is responsible  for transmitting/receiving messages, the  sensing subsystem that collects  data, and  the  power supply  which  powers the  complete sensor  node
 \cite{ref112}. Each  of the first three subsystems  can be turned on or  off depending on  the current status  of the sensor.   Energy consumption
 In this dissertation, the coverage protocols have been used an energy consumption model proposed by~\cite{ref111} and based on \cite{ref112} with slight  modifications.  The energy consumption for  sending/receiving the packets is added, whereas the  part related to the sensing range is removed because we consider a fixed sensing range.
 For our energy consumption model, we refer to the sensor node Medusa~II which uses an Atmels  AVR ATmega103L microcontroller~\cite{ref112}. The typical architecture  of a  sensor  is composed  of  four  subsystems: the  MCU subsystem which is capable of computation, communication subsystem (radio) which is responsible  for transmitting/receiving messages, the  sensing subsystem that collects  data, and  the  power supply  which  powers the  complete sensor  node
 \cite{ref112}. Each  of the first three subsystems  can be turned on or  off depending on  the current status  of the sensor.   Energy consumption


@@ -476,7 +478,7 @@ COMPUTATION & on & on & on & 26.83 \\
 \end{table}
 
 For the sake of simplicity we ignore  the energy needed to turn on the radio, to start up the sensor node, to move from one status to another, etc.
 \end{table}
 
 For the sake of simplicity we ignore  the energy needed to turn on the radio, to start up the sensor node, to move from one status to another, etc.

-Thus, when a sensor becomes active (i.e., it has already chosen its status), it can turn  its radio  off to  save battery. The value of energy spent to send a 1-bit-content message is  obtained by using  the equation in  ~\cite{ref112} to calculate  the energy cost  for transmitting  messages and  we propose  the same
+Thus, when a sensor becomes active (i.e., it has already chosen its status), it can turn  its radio  off to  save battery. The value of energy spent to send a 1-bit-content message is  obtained by using  the equation in  ~\cite{ref112} to calculate  the energy cost for transmitting  messages and  we propose  the same

 value for receiving the packets. The energy  needed to send or receive a 1-bit packet is equal to $0.2575~mW$.
 
 
 value for receiving the packets. The energy  needed to send or receive a 1-bit packet is equal to $0.2575~mW$.