\end{enumerate}
-\section{Energy Consumption Models:}
+\section{Energy Consumption Modeling:}
\label{ch1:sec:9}
\indent The WSNs have been received a lot of interest because their low energy consumption sensor nodes. Since the sensor node has a limited power battery; therefore, one of the most critical issues in WSNs is how to reduce the energy consumption of sensor nodes so as to prolong the network lifetime as long as possible. In order to model the energy consumption, four states for a sensor node have been used~\cite{ref140}: transmission, reception, listening, and sleeping; in addition, two states that should be taken into account: computation and sensed data acquisition. The main tasks of each of these states include:
\end{enumerate}
-In this section, two energy consumption models are explained. The first model called radio energy dissipation model and the second model represent our energy consumption model, which has been used by the proposed protocols in this dissertation.
+%In this section, two energy consumption models are explained. The first model called radio energy dissipation model and the second model represent our energy consumption model, which has been used by the proposed protocols in this dissertation.
-\subsection{Radio Energy Dissipation Model:}
-\label{ch1:sec9:subsec1}
+%\subsection{Radio Energy Dissipation Model:}
+%\label{ch1:sec9:subsec1}
\indent Since the communication unit is the most energy-consuming part inside the sensor node, therefore, many authors are used the radio energy dissipation model that proposed in~\cite{ref109,ref110} as energy consumption model during the simulation and evaluation of their works in WSNs. Figure~\ref{RDM} shows the radio energy dissipation model.
\begin{figure}[h!]
\centering
\indent The radio energy dissipation model have been considered only the energy, which is consumed by the communication part inside the sensor node; however, in order to achieve a more accurate model, it is necessary to take into account the energy is consumed by the other parts inside the sensor node such as: computation unit and sensing unit.
-\subsection{Our Energy Consumption Model:}
-\label{ch1:sec9:subsec2}
-\indent In this dissertation, the coverage protocols have been used an energy consumption model proposed by~\cite{ref111} and based on \cite{ref112} with slight modifications. The energy consumption for sending/receiving the packets is added, whereas the part related to the sensing range is removed because we consider a fixed sensing range.
-
-\indent For our energy consumption model, we refer to the sensor node Medusa~II which uses an Atmels AVR ATmega103L microcontroller~\cite{ref112}. The typical architecture of a sensor is composed of four subsystems: the MCU subsystem which is capable of computation, communication subsystem (radio) which is responsible for transmitting/receiving messages, the sensing subsystem that collects data, and the power supply which powers the complete sensor node \cite{ref112}. Each of the first three subsystems can be turned on or off depending on the current status of the sensor. Energy consumption (expressed in milliWatt per second) for the different status of the sensor is summarized in Table~\ref{table1}.
-
-\begin{table}[ht]
-\caption{The Energy Consumption Model}
-% title of Table
-\centering
-% used for centering table
-\begin{tabular}{|c|c|c|c|c|}
-% centered columns (4 columns)
- \hline
-%inserts double horizontal lines
-Sensor status & MCU & Radio & Sensing & Power (mW) \\ [0.5ex]
-\hline
-% inserts single horizontal line
-LISTENING & on & on & on & 20.05 \\
-% inserting body of the table
-\hline
-ACTIVE & on & off & on & 9.72 \\
-\hline
-SLEEP & off & off & off & 0.02 \\
-\hline
-COMPUTATION & on & on & on & 26.83 \\
-%\hline
-%\multicolumn{4}{|c|}{Energy needed to send/receive a 1-bit} & 0.2575\\
- \hline
-\end{tabular}
-
-\label{table1}
-% is used to refer this table in the text
-\end{table}
-
-\indent For the sake of simplicity we ignore the energy needed to turn on the radio, to start up the sensor node, to move from one status to another, etc. Thus, when a sensor becomes active (i.e., it has already chosen its status), it can turn its radio off to save battery. The value of energy spent to send a 1-bit-content message is obtained by using the equation in ~\cite{ref112} to calculate the energy cost for transmitting messages and we propose the same value for receiving the packets. The energy needed to send or receive a 1-bit packet is equal to $0.2575~mW$.
+%\subsection{Our Energy Consumption Model:}
+%\label{ch1:sec9:subsec2}
\section{Conclusion}
\label{ch1:sec:10}
-\indent In this chapter, an overview about the wireless sensor networks have been presented that represent our focus in this dissertation. The structure of the the typical wireless sensor network and the main components of the sensor nodes have been demonstrated. Several types of wireless sensor networks are described. Various fields of applications covering a wide spectrum for a WSNs have been presented, including health, home, environmental, military, and industrial applications. As demonstrated, since sensor nodes have limited battery life; since it is impossible to replace batteries, especially in remote and hostile environments; the limited power of a battery represents the critical challenge in WSNs. The main challenges in WSNs have been explained; on the other hand, the energy efficient solutions have been proposed in order to handle these challenges through energy conservation to prolong the network lifetime. Many energy efficient mechanisms have been illustrated, which are aimed to reduce the energy consumption by the different units of the wireless sensor nodes in WSNs. The definition of the network lifetime has been presented and in different contexts. The problem of the coverage is explained, where constructing energy efficient coverage protocols one of the main scientific research challenges in WSNs. This chapter highlights the main design issues for the coverage problems that need to be considered during designing a coverage protocol for WSNs. In addition, some energy consumption models have been demonstrated.
+\indent In this chapter, an overview about the wireless sensor networks have been presented that represent our focus in this dissertation. The structure of the the typical wireless sensor network and the main components of the sensor nodes have been demonstrated. Several types of wireless sensor networks are described. Various fields of applications covering a wide spectrum for a WSNs have been presented, including health, home, environmental, military, and industrial applications. As demonstrated, since sensor nodes have limited battery life; since it is impossible to replace batteries, especially in remote and hostile environments; the limited power of a battery represents the critical challenge in WSNs. The main challenges in WSNs have been explained; on the other hand, the energy efficient solutions have been proposed in order to handle these challenges through energy conservation to prolong the network lifetime. Many energy efficient mechanisms have been illustrated, which are aimed to reduce the energy consumption by the different units of the wireless sensor nodes in WSNs. The definition of the network lifetime has been presented and in different contexts. The problem of the coverage is explained, where constructing energy efficient coverage protocols one of the main scientific research challenges in WSNs. This chapter highlights the main design issues for the coverage problems that need to be considered during designing a coverage protocol for WSNs. In addition, the energy consumption Modeling have been demonstrated.
