From: ali Date: Sun, 28 Jun 2015 13:02:22 +0000 (+0200) Subject: Update by Ali X-Git-Url: https://bilbo.iut-bm.univ-fcomte.fr/and/gitweb/ThesisAli.git/commitdiff_plain/c46884fa798f3a13361244344e58a641ff9e6ad8 Update by Ali --- diff --git a/CHAPITRE_05.tex b/CHAPITRE_05.tex index 733232c..5a39fd7 100644 --- a/CHAPITRE_05.tex +++ b/CHAPITRE_05.tex @@ -330,7 +330,7 @@ Obviously, in that case, DESK and GAF have fewer active nodes since they have a %\subsection{Stopped simulation runs} %\label{ch5:sec:03:02:03} -Figure~\ref{fig6} reports the cumulative percentage of stopped simulations runs per round for 150 deployed nodes. This figure gives the breakpoint for each method. \\ \\ \\ \\ +Figure~\ref{fig6} reports the cumulative percentage of stopped simulations runs per round for 150 deployed nodes. This figure gives the breakpoint for each method. DESK stops first, after approximately 45~rounds, because it consumes the more energy by turning on a large number of redundant nodes during the sensing phase. GAF stops secondly for the same reason than DESK. MuDiLCO overcomes DESK and GAF because the optimization process distributed on several subregions leads to coverage preservation and so extends the network lifetime. Let us emphasize that the simulation continues as long as a network in a subregion is still connected. \\ @@ -370,7 +370,7 @@ network sizes, for $Lifetime_{95}$ and $Lifetime_{50}$. The results show that MuDiLCO is the most competitive from the energy consumption point of view. The other approaches have a high energy consumption due to activating a larger number of redundant nodes, as well as the energy consumed during the different status of the sensor node. Among the different versions of our protocol, the MuDiLCO-7 one consumes more energy than the other versions. This is easy to understand since the bigger the number of rounds and the number of sensors involved in the integer program, the larger the time computation to solve the optimization problem. To improve the performances of MuDiLCO-7, we should increase the number of subregions in order to have fewer sensors to consider in the integer program. -\\ \\ \\ + \item {{\bf Execution time}} @@ -391,14 +391,15 @@ seconds (needed to solve optimization problem) for different values of $T$. The \end{figure} As expected, the execution time increases with the number of rounds $T$ taken into account to schedule the sensing phase. The times obtained for $T=1,3$ or $5$ seem bearable, but for $T=7$ they become quickly unsuitable for a sensor node, especially when the sensor network size increases. Again, we can notice that if we want to schedule the nodes activities for a large number of rounds, -we need to choose a relevant number of subregions in order to avoid a complicated and cumbersome optimization. On the one hand, a large value for $T$ permits to reduce the energy overhead due to the three pre-sensing phases, on the other hand a leader node may waste a considerable amount of energy to solve the optimization problem. \\ +we need to choose a relevant number of subregions in order to avoid a complicated and cumbersome optimization. +On the one hand, a large value for $T$ permits to reduce the energy overhead due to the three pre-sensing phases, on the other hand a leader node may waste a considerable amount of energy to solve the optimization problem. \\ \\ \\ \\ \\ \\ \\ \item {{\bf Network lifetime}} %\subsection{Network lifetime} %\label{ch5:sec:03:02:06} The next two figures, Figures~\ref{fig8}(a) and \ref{fig8}(b), illustrate the network lifetime for different network sizes, respectively for $Lifetime_{95}$ and $Lifetime_{50}$. Both figures show that the network lifetime increases together with the number of sensor nodes, whatever the protocol, thanks to the node density which results in more and more redundant nodes that can be deactivated and thus save energy. Compared to the other approaches, our MuDiLCO -protocol maximizes the lifetime of the network. In particular, the gain in lifetime for a coverage over 95\% is greater than 38\% when switching from GAF to MuDiLCO-3. \\ \\ \\ +protocol maximizes the lifetime of the network. In particular, the gain in lifetime for a coverage over 95\% is greater than 38\% when switching from GAF to MuDiLCO-3. \begin{figure}[h!] \centering @@ -414,10 +415,11 @@ protocol maximizes the lifetime of the network. In particular, the gain i \end{figure} -\end{enumerate} The slight decrease that can be observed for MuDiLCO-7 in case of $Lifetime_{95}$ with large wireless sensor networks results from the difficulty of the optimization problem to be solved by the integer program. This point was already noticed in \ref{subsec:EC} devoted to the energy consumption, since network lifetime and energy consumption are directly linked. +\end{enumerate} + \section{Conclusion} \label{ch5:sec:05}