-The Spartan 6 used in our architecture has hard constraint : it has no
-built-in floating point units. Obviously, it is possible to use some
-existing "black-boxes" for double precision operations. But they have
-a quite long latency. It is much simpler to exclusively use integers,
-with a quantization of all double precision values. Obviously, this
-quantization should not decrease too much the precision of
-results. Furthermore, it should not lead to a design with a huge
-latency because of operations that could not complete during a single
-or few clock cycles. Divisions are in this case and, moreover, they
-need an varying number of clock cycles to complete. Even
-multiplications can be a problem : DSP48 take inputs of 18 bits
-maximum. For larger multiplications, several DSP must be combined,
-increasing the latency.
-
-Nevertheless, the hardest constraint does not come from the FPGA
-characteristics but from the algorithms. Their VHDL implentation will
-be efficient only if they can be fully (or near) pipelined. By the
-way, the choice is quickly done : only a small part of SPL can be.
-Indeed, the computation of spline coefficients implies to solve a
-tridiagonal system $A.m = b$. Values in $A$ and $b$ can be computed
-from incoming pixels intensity but after, the back-solve starts with
-the lastest values, which breaks the pipeline. Moreover, SPL relies on
-interpolating far more points than profile size. Thus, the end
-of SPL works on a larger amount of data than the beginning, which
-also breaks the pipeline.
-
-LSQ has not this problem : all parts except the dichotomial search
-work on the same amount of data, i.e. the profile size. Furthermore,
-LSQ needs less operations than SPL, implying a smaller output
-latency. Consequently, it is the best candidate for phase
-computation. Nevertheless, obtaining a fully pipelined version
-supposes that operations of different parts complete in a single clock
-cycle. It is the case for simulations but it completely fails when
-mapping and routing the design on the Spartan6. By the way,
-extra-latency is generated and there must be idle times between two
-profiles entering into the pipeline.
-
-%%Before obtaining the least bitstream, the crucial question is : how to
+The Spartan 6 used in our architecture has a hard constraint: it has no built-in
+floating point units. Obviously, it is possible to use some existing
+"black-boxes" for double precision operations. But they have a quite long
+latency. It is much simpler to exclusively use integers, with a quantization of
+all double precision values. Obviously, this quantization should not decrease
+too much the precision of results. Furthermore, it should not lead to a design
+with a huge latency because of operations that could not complete during a
+single or few clock cycles. Divisions are in this case and, moreover, they need
+a varying number of clock cycles to complete. Even multiplications can be a
+problem: DSP48 take inputs of 18 bits maximum. For larger multiplications,
+several DSP must be combined, increasing the latency.
+
+Nevertheless, the hardest constraint does not come from the FPGA characteristics
+but from the algorithms. Their VHDL implentation will be efficient only if they
+can be fully (or near) pipelined. By the way, the choice is quickly done: only a
+small part of SPL can be. Indeed, the computation of spline coefficients
+implies to solve a tridiagonal system $A.m = b$. Values in $A$ and $b$ can be
+computed from incoming pixels intensity but after, the back-solve starts with
+the lastest values, which breaks the pipeline. Moreover, SPL relies on
+interpolating far more points than profile size. Thus, the end of SPL works on a
+larger amount of data than the beginning, which also breaks the pipeline.
+
+LSQ has not this problem: all parts except the dichotomial search work on the
+same amount of data, i.e. the profile size. Furthermore, LSQ needs less
+operations than SPL, implying a smaller output latency. Consequently, it is the
+best candidate for phase computation. Nevertheless, obtaining a fully pipelined
+version supposes that operations of different parts complete in a single clock
+cycle. It is the case for simulations but it completely fails when mapping and
+routing the design on the Spartan6. By the way, extra-latency is generated and
+there must be idle times between two profiles entering into the pipeline.
+
+%%Before obtaining the least bitstream, the crucial question is: how to
