-In this section, we compare our scaling factors selection algorithm
-with Spiliopoulos et al. algorithm \cite{Spiliopoulos_Green.governors.Adaptive.DVFS}.
-They developed an online frequency selecting algorithm running over multicore architecture.
-The algorithm predicted both the energy and performance during the runtime of the program, then
-selecting the frequencies that minimized the energy and delay products (EDP), $EDP=Enegry * Delay$.
-To be able to compare with this algorithm, we used our energy and execution time models in prediction process,
-equations (\ref{eq:energy}) and (\ref{eq:fnew}). Also their algorithm is adapted to taking into account
-the heterogeneous platform to starts selecting the
-initial frequencies using the equation (\ref{eq:Fint}). The algorithm built to test all possible frequencies as
-a brute-force search algorithm.
-
-The comparison results of running NAS benchmarks class C on 8 or 9 nodes are
-presented in table \ref{table:compare_EDP}. The results show that our algorithm has a biggest energy saving percentage,
-on average it has 29.76\% and thier algorithm has 25.75\%,
-while the average of performance degradation percentage is approximately the same, the average for our algorithm is
-equal to 3.89\% and for their algorithm is equal to 4.03\%. In general, our algorithm outperforms
-Spiliopoulos et al. algorithm in term of energy and performance tradeoff see figure (\ref{fig:compare_EDP}).
-This because our algorithm maximized the difference (the distance) between the energy saving and the performance degradation
-comparing to their EDP optimization function. It is also keeps the frequency of the slowest node without change
-that gave some enhancements to the energy and performance tradeoff.
-
-
-\begin{table}[h]
- \caption{Comparing the proposed algorithm}
- \centering
-\begin{tabular}{|l|l|l|l|l|l|l|l|}
-\hline
-\multicolumn{2}{|l|}{\multirow{2}{*}{\begin{tabular}[c]{@{}l@{}}Program \\ name\end{tabular}}} & \multicolumn{2}{l|}{Energy saving \%} & \multicolumn{2}{l|}{Perf. degradation \%} & \multicolumn{2}{l|}{Distance} \\ \cline{3-8}
-\multicolumn{2}{|l|}{} & EDP & MaxDist & EDP & MaxDist & EDP & MaxDist \\ \hline
-\multicolumn{2}{|l|}{CG} & 27.58 & 31.25 & 5.82 & 7.12 & 21.76 & 24.13 \\ \hline
-\multicolumn{2}{|l|}{MG} & 29.49 & 33.78 & 3.74 & 6.41 & 25.75 & 27.37 \\ \hline
-\multicolumn{2}{|l|}{LU} & 19.55 & 28.33 & 0.0 & 0.01 & 19.55 & 28.22 \\ \hline
-\multicolumn{2}{|l|}{EP} & 28.40 & 27.04 & 4.29 & 0.49 & 24.11 & 26.55 \\ \hline
-\multicolumn{2}{|l|}{BT} & 27.68 & 32.32 & 6.45 & 7.87 & 21.23 & 24.43 \\ \hline
-\multicolumn{2}{|l|}{SP} & 20.52 & 24.73 & 5.21 & 2.78 & 15.31 & 21.95 \\ \hline
-\multicolumn{2}{|l|}{FT} & 27.03 & 31.02 & 2.75 & 2.54 & 24.28 & 28.48 \\ \hline
-
-\end{tabular}
-\label{table:compare_EDP}
-\end{table}
+In this section, the scaling factors selection algorithm
+is compared to Spiliopoulos et al. algorithm \cite{Spiliopoulos_Green.governors.Adaptive.DVFS}.
+They developed a green governor that regularly applies an online frequency selecting algorithm to reduce the energy consumed by a multicore architecture without degrading much its performance. The algorithm selects the frequencies that minimize the energy and delay products, $EDP=Enegry*Delay$ using the predicted overall energy consumption and execution time delay for each frequency.
+ To fairly compare both algorithms, the same energy and execution time models, equations (\ref{eq:energy}) and (\ref{eq:fnew}), were used for both algorithms to predict the energy consumption and the execution times. Also Spiliopoulos et al. algorithm was adapted to start the search from the
+initial frequencies computed using the equation (\ref{eq:Fint}). The resulting algorithm is an exhaustive search algorithm that minimizes the EDP and has the initial frequencies values as an upper bound.
+
+Both algorithms were applied to the parallel NAS benchmarks to compare their efficiency. Table \ref{table:compare_EDP} presents the results of comparing the execution times and the energy consumptions for both versions of the NAS benchmarks while running the class C of each benchmark over 8 or 9 heterogeneous nodes. \textcolor{red}{The results show that our algorithm gives better energy savings than Spiliopoulos et al. algorithm,
+on average it is up to 17\% higher for energy saving compared to their algorithm. The average of performance degradation percentage using our method is higher on average by 3.82\%.}
+
+For all benchmarks, our algorithm outperforms
+Spiliopoulos et al. algorithm in term of energy and performance tradeoff \textcolor{red}{(on average it has up to 21\% of distance)}, see figure (\ref{fig:compare_EDP}) because it maximizes the distance between the energy saving and the performance degradation values while giving the same weight for both metrics.
+
